stratopican_setup

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
stratopican_setup [2021/03/04 14:00] – [Board status upgrade] nikolalstratopican_setup [2022/09/19 11:34] (current) – external edit 127.0.0.1
Line 3: Line 3:
   * For the CAN bus, we use the built in 120Ω terminal resistor, activated by bridging jumper JP3.   * For the CAN bus, we use the built in 120Ω terminal resistor, activated by bridging jumper JP3.
   * For the RS-485, we use the built in bias network of resistors, activated by bridging jumpers JP1, JP2 and JP4.   * For the RS-485, we use the built in bias network of resistors, activated by bridging jumpers JP1, JP2 and JP4.
-===== Watchdog ===== +===== Logic Controller Configuration ===== 
-The watchdog of the Strato Pi has to be configured for our use. First the firmware has to be updated to 3.5. Then we can connect to the serial interface. +Configuration of the StratoPi logic controller is performed through a 1200 baud, 8N1 UART connection at the following pins (5V if board is not connected to RPI)
  
 ^ USBUART      ^ Stratopi       ^ Corresponding pin on RPI          ^ ^ USBUART      ^ Stratopi       ^ Corresponding pin on RPI          ^
Line 12: Line 11:
 | RX    | 35     | GPIO19        | | RX    | 35     | GPIO19        |
 | TX    | 33     | GPIO13        | | TX    | 33     | GPIO13        |
 +Pin counting begins with the pin closest to the screw terminals as 1.
  
-Where counting begins with the pin closest to the screw terminals as 1+This configuration assumes FW 3.5 on the logic controller. 
 + 
 +==== Watchdog ==== 
 +  * ''XWED'' Set the watchdog enable mode to disabled (Badly named, in this mode, it's enabled by setting WatchdogEnable gpio pin from the RPI). 
 +  * ''XWH00005'' Set timeout to 5 sec. 
 +  * ''XWW00001'' Set the watchdog forced shutdown timeout to 1sec(min). 
 +  * ''XCCS''  Make configuration permanent.
  
 ==== RS-485 ==== ==== RS-485 ====
Line 28: Line 34:
  
  
-^ Board      ^ Firmware       ^ Watchdog ^ RS-485 ^ +^ Board      ^ Firmware       ^ Configured ^ Location ^ Note ^ 
-| SPBC12X-FX314618SC-296 | 3.5 | Configured | Configured | +| SPBC12X-FX314618SC-296 | 3.5 | X | Loose | | 
-| SPBC12X-FX314618SC-297 | 3.5 | Configured | |+| SPBC12X-FX314618SC-297 | 3.5 | X | Loose | PPS lever-shifter | 
 +| SPBC12X-FX314618SC-292 | 3.5 | X | Loose |  | 
 +| SPBC12X-FX432220SC-F21200269 | 4.3/0.8 | X | ntnu-otter-02 |  | 
 +| SPBC12X-FX314618SC-F21200097 | 4.3/0.8 | X | ntnu-otter-01 |  | 
 +| SPBC12X-FX314618SC-F21200301 | 4.3/0.8 | X | ntnu-otter-03 |  | 
  • stratopican_setup.1614862851.txt.gz
  • Last modified: 2022/09/19 11:33
  • (external edit)